Hamlet HPS01NW Manual de usuario

USB WIRELESS PRINT SERVER NETWORK ADAPTER FOR USB PRINTER SHARING User Manual HPS01NW www.hamletcom.com

10 Internet Printing Protocol Windows NT/2000/XP/2003/Vista/7 Printing via the internet to Internet Printing Protocol- enabled print server Allows sav

11 3 Software Installation The PSAdmin is a proprietary Windows-based management program that can assist you in configuring and managing your print se

12 3. Choose Setup Wizard to install the print server and configure the connected printer. Note: The setup CD will install the print server’s driver

13 5. From the Select A Print Sever screen, select the print server that you want to configure and click Next.

14 6. On the Change Settings screen, select No or Yes: Click No if you want the print server to keep using the default IP address and keep the defau

15 • On the Basic Wireless Settings screen, select Communication Type according to your network: - Infrastructure - Ad-Hoc • Enter the proper SSID of

16 8. Click Add New Printer to launch Windows Add Printer Wizard. 9. Click Next and select Local Printer, make sure the Automatically detect and in

17 10. Make sure the Use the following port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down list. Then click Ne

18 12. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the p

19 15. From Windows system, go to start  Printers and Faxes and highlight your newly installed printer. 16. Right-click, select Properties  Port

2 Dear Customer, thanks for choosing an Hamlet product. Please carefully follow the instructions for its use and maintenance and, once this item has r

20 17. Go to General; click Print Test Page to verify the configuration. 18. Done. Note: If you want to install more print servers, start setup wiza

21 Wizard Wizard is a configuration program that can assist you in setting up the necessary parameters for your print server device to function. Setup

22 5. (Optional) In the Gateway field, type the IP address of gateway. 6. When done, click OK button. The program will save the above settings into

23 Manual Setup Manual Setup is a configuration program designed for more experienced users of NetWare. To setup the print server by using Manual Setu

24 Properties – TCP/IP Options The TCP/IP options allow you to modify the print server’s TCP/IP settings. Each option is detailed as follows. Obtai

25 Upgrade Upgrade allows the user to upgrade the print server device. In order to upgrade the unit please perform the steps as follows: 1. Click Upg

26 Multiple Print Queues Configuration (Novell Netware) To configure the print server to service multiple print queues, please follow the instructions

27 4 Internet Printer Connection and HP Web JetAdmin IPP Overview Print server(s) support the Internet Printing Protocol (IPP). Using the appropriate

28 7. It will check print server to connect to HP printer, if not, it will appear as follow picture. Then Click OK. 8. Select the appropriate pri

29 HP Web JetAdmin Overview HP Web JetAdmin allows you to use a Web browse to revise, view, manage and diagnose devices connected to the print server

3 Table of Contents 1 Introduction...

30 Removing HP Web JetAdmin Utility To remove HP Web JetAdmin software from your web server, use the uninstall program provided with the software pack

31 5 Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that can be accessed through a supported web br

32 System Status 1. Click Status, it then appears the sub-menu. 2. Click System, it then as shown in the following picture. Print Server Name: This

33 Printer Status 1. Click Status, it then appears the sub-menu. 2. Click Printer, it then as shown in the following picture. Manufacturer: This opt

34 Wireless Status 1. Click Status, it then appears the sub-menu. 2. Click Wireless, it then as shown in the following picture. Mode: This option sh

35 TCP/IP Status 1. Click Status, it then appears the sub-menu. 2. Click TCPIP, it then as shown in the following picture. Use DHCP/BOOTP: This opti

36 Netware Status 1. Click Status, it then appears the sub-menu. 2. Click Netware it then as shown in the following picture. General Settings Print

37 AppleTalk Status 1. Click Status, it then appears the sub-menu. 2. Click AppleTalk, it then as shown in the following picture. AppleTalk Settings

38 SNMP Status 1. Click Status, it then appears the sub-menu. 2. Click SNMP, it then as shown in the following picture. SNMP Communities: This optio

39 SMB Status 1. Click Status, it then appears the sub-menu. 2. Click SMB, it then as shown in the following picture. Workgroup Name: This option

4 Wireless Setup ... 42 TCP/IP Setup ...

40 Setup Menu Meanwhile, you have finished the IP address configuration with print server. You should use web browser to configure the print server.

41 SMTP Server IP Address: This option allows you to input the IP address of your Email SMTP server. Administrator E-mail Address: This option allows

42 Wireless Setup 1. Click Setup, it then appears the sub-menu. 2. Click Wireless, it then as shown in the following picture. Basic Settings Netwo

43 Security Type Disable: Disable the security settings WEP: Enable the WEP (Wired Equivalent Privacy) encryption security. Encryption Type: Select

44 TCP/IP Setup 1. Click Setup, it then appears the sub-menu. 2. Click TCP/IP, it then as shown in the following picture. DHCP/BOOTP: This option al

45 NetWare Setup 1. Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Select NetWare and type in the Print server that cr

46 Installing Print Server on NetWare 4.x/5.x Due to its architecture and functionality, the print server must work under NetWare 4.x/5.x NDS Bindery

47 AppleTalk Setup The print server can print jobs submitted from Macintosh workstations connected to an Ethernet using AppleTalk protocol. The basic

48 Type: In this option, the LaserWriter of printer type by default (recommended). Binary Protocol: In this option, data format includes ASCII, TBCP a

49 SNMP Setup TCP/IP networks use a standard management protocol called Simple Network Management Protocol (SNMP). SNMP is widely used in the industry

5 1 Introduction Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly on

50 snmp.snmpEnableAuthenTraps Enables or disables the function of sending SNMP Authentication Failure trap message to the network administrator, if

51 SMB Setup The print server supports the SMB (Server Message Block)protocol, user can send the print jobs through Network Neighborhood without insta

52 6 Network Print Monitor Preparation The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Microsoft Windows system. Please make su

53 Note: Using TCP/IP protocol to access the print server requires well-configured TCP/IP settings. If you are not familiar with these settings, plea

54 Windows 95/98/Me/NT/2000/XP/2003 manual Installation Procedure Please perform the steps as follows to ensure a smooth installation: 1. Run Setup f

55 16. The Add Port box will then appear, along with the print server’s Node ID (The last 6 digits of the Node ID, located on the back of the print se

56 Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP/2003 To provide users an easiest way to remove all of the Network Print Port compone

57 7 TCP/IP LPR Port Printing Installation Basic TCP/IP Installation Overview When installing your print server in a TCP/IP environment, IP addresses

58 5. From the Printer Ports box as shown in the following picture, select the LPR Port. 6. The Add LPR compatible printers box will then appear

59 Windows 2000/XP/2003/Vista/7 standard TCP/IP Port Printing Installation 1. Click Start, point to Settings, and select Printer. 2. Run Add Printer,

6 LED Indicators LED State Indication On (Orange) When power switched on, the Status indicator will flash five times, and then on. The LAN port is l

60 6. In the Add Standard TCP/IP Printer Port Wizard box as shown in the following picture, Select Custom, Click Settings button, and click Next. 7

61 12. A message reading, “To confirm that the printer is installed properly, you can print a test page”. Select Yes (Recommended) and click Finish. 1

62 UNIX Installation After the static IP address is assigned, the Print Server is ready to be configured. For some UNIX/Linux systems, we include the

63 Redhat Linux 9 (Fedora) The Print Server can work under any Linux-based systems, including Slackware, RedHat, etc, without any problems. Basically

64 7. In the Name field, type a user-defined name, click Forward. 8. In the Queue Type field, choose Networked UNIX. 9. In the Server field, type

65 12. In the Printer field, choose Postscript Printer. 13. Choose the model of printer and click Forward. 14. Done.

66 8 Upgrading Print Server Overview Upgrading print server will allow you to upgrade its firmware inside the print server while the newer software ve

67 Upgrading the print server from UNIX (Through TCP/IP) 1. Log in as root 2. Ensure binary file is located in your current working directory. 3. Ty

68 9 Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in thi

69 Windows 95/98/Me/NT/2000/XP/2003/Vista/7 Troubleshooting Multi-Segment LAN Environment Installation (through the Network Print Port) If your print

7 WPS WiFi Protected Setup Printer Server supports WiFi Protected Setup (WPS), which is an easy way to set up a secure wireless network. WPS is an in

70 Moving the print server to a new Segment If the print server is moved from one network segment to another after the initial installation, through t

71 Moving Your Computer to A New Segment If you are using the print server through the Network Print Port on your NT or Windows 95/98/Me computer and

72 B. The print server's IP address is duplicated or is as same as another computer's IP address on the network. If this is the case, pleas

73 file and quit from your editor. Please note, in this step you must specify an IP address which is valid on Segment B, such as 192.72.214.100 in thi

74 Appendix SMB Printing with Windows XP 1. Enable the SMB settings from the print server’s WEB configuration. Assume your computers use the “WORKGROU

75 2. Now you can find the print server from the SMB workgroup of Windows. Then, double click it. 3. Double click it again.

76 4. Now you have to install the printer’s driver. 5. Choose it from the “Add Printer Wizard”.

77 6. Install printer successfully. 7. Now, you can find your printer’s icon and you can use the SMB printing mode.

78 Reset Button Reboot the Print server 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it. WARN

79 Frequently Asked Questions Question A Print jobs are sent to the print queue successfully, but fail to be sent to the printer. Possible explanatio

8 Network Environment Wired Network with Print Server PrinterPrint ServerComputer Computer ComputerHUB Wireless Network with Print Server Infracstru

80 Question D The Status LED light keeps blinking after POST. Possible explanation and solution The last upgrade process was not completed. The print

9 2 Print Server Installation Preparation To meet users’ network printing needs in today’s heterogeneous and multiple protocol networking environments